1.one thousand grams; the basic unit of mass adopted under the Systeme International d'Unites"a kilogram is approximately 2.2 pounds"
voir la définition de Wikipedia
unité de masse (fr)[Classe]
|Unit system:||SI base unit|
|1 kg in...||is equal to...|
|U.S. customary||≈ 2.205 pounds|
|Natural units|| ≈ 4.59×107 Planck masses
1.356392608(60)×1050 hertz [Note 1]
The kilogram or kilogramme (SI symbol: kg), also known as the kilo, is the base unit of mass in the International System of Units and is defined as being equal to the mass of the International Prototype Kilogram (IPK), which is almost exactly equal to the mass of one liter of water. The avoirdupois (or international) pound, used in both the Imperial system and U.S. customary units, is defined as exactly 0.45359237 kg, making one kilogram approximately equal to 2.2046 avoirdupois pounds.
In everyday usage, the mass of an object given in kilograms is often referred to as its weight, which is the measure of the gravitational force—or heaviness—of an object. Weight given in kilograms is technically the non‑SI unit of measure known as the kilogram-force. The equivalent unit of force in the avoirdupois system of measurement is the pound-force. In strict scientific contexts, forces are typically measured with the SI unit newton.
The kilogram is the only SI base unit with an SI prefix as part of its name. It is also the only SI unit that is still directly defined by an artifact rather than a fundamental physical property that can be reproduced in different laboratories. Four of the seven base units in the SI system are defined relative to the kilogram so its stability is important.
The International Prototype Kilogram is kept in the custody of the International Bureau for Weights and Measures (BIPM) who hold it on behalf of the General Conference on Weights and Measures (CGPM). After the International Prototype Kilogram had been found to vary in mass over time, the International Committee for Weights and Measures (CIPM) recommended in 2005 that the kilogram be redefined in terms of a fundamental constant of nature. At its 2011 meeting, the General Conference on Weights and Measures (CGPM) agreed in principle that the kilogram should be redefined in terms of the Planck constant, but deferred a final decision until its next meeting, scheduled for 2014.
The words "kilogramme" and "kilogram" are both derived from the French word "kilogramme", which itself was derived from the Greek words "χίλιοι" (chilioi), meaning "thousand" and "γράμμα" (gramma) meaning "a small weight". The word "kilogramme" was written into French law in 1795 and the French spelling was adopted in the United Kingdom when the word was used for the first time in English in 1797, with the spelling "kilogram" being adopted in the United States. In the United Kingdom both spellings are used, with "kilogram" having become by far the more common.[Note 2] UK law regulating the units to be used when trading by weight or measure does not prevent the use of either spelling.
In the 19th century the French word "kilo", a shortening of "kilogramme", was imported into the English language where it has been used to mean both kilogram and kilometre. While "kilo" is acceptable in many generalist texts, for example The Economist, its use is typically considered inappropriate in certain applications including scientific, technical and legal writing, where authors should adhere strictly to SI nomenclature." When the United States Congress gave the metric system a legal status in 1866, it permitted the use of the word "kilo" as an alternative to the word "kilogram", but in 1990 revoked the status of the word "kilo".
In 1948 the CGPM commissioned the CIPM to "to make recommendations for a single practical system of units of measurement, suitable for adoption by all countries adhering to the Metre Convention". This led to the launch of SI in 1960 and the subsequent publication of the "SI Brochure," which stated that "It is not permissible to use abbreviations for unit symbols or unit names ...".[Note 3]
The kilogram is a unit of mass, the measurement of which corresponds to the general, everyday notion of how “heavy” something is. Physically speaking, mass is an inertial property; that is, the tendency of an object to remain at constant velocity unless acted upon by an outside force. According to Sir Isaac Newton's 325-year-old laws of motion and an important formula that sprang from his work, F = ma, an object with a mass, m, of one kilogram will accelerate, a, at one meter per second per second (about one-tenth the acceleration due to earth’s gravity)[Note 4] when acted upon by a force, F, of one newton.
While the weight of matter is dependent upon the strength of gravity, the mass of matter is invariant.[Note 5] Accordingly, for astronauts in microgravity, no effort is required to hold objects off the cabin floor; they are “weightless”. However, since objects in microgravity still retain their mass and inertia, an astronaut must exert ten times as much force to accelerate a 10‑kilogram object at the same rate as a 1‑kilogram object.
On earth, a common swing set can demonstrate the relationship of force, mass, and acceleration without being appreciably influenced by weight (downward force). If one were to stand behind a large adult sitting stationary in a swing and give him a strong push, the adult would accelerate relatively slowly and swing only a limited distance forwards before beginning to swing backwards. Exerting that same effort while pushing on a small child would produce much greater acceleration.
On 7 April 1795, the gram was decreed in France to be equal to “the absolute weight of a volume of water equal to the cube of the hundredth part of the meter, at the temperature of melting ice.” The concept of using a specified volume of water to define a unit measure of mass was first advanced by the English philosopher John Wilkins in 1668.
Since trade and commerce typically involve items significantly more massive than one gram, and since a mass standard made of water would be inconvenient and unstable, the regulation of commerce necessitated the manufacture of a practical realization of the water-based definition of mass. Accordingly, a provisional mass standard was made as a single-piece, metallic artifact one thousand times as massive as the gram—the kilogram.
At the same time, work was commissioned to precisely determine the mass of a cubic decimeter (one liter) of water.[Note 6] Although the decreed definition of the kilogram specified water at 0 °C—its highly stable temperature point—the French chemist Louis Lefèvre-Gineau and the Italian naturalist Giovanni Fabbroni after several years of research chose to redefine the standard in 1799 to water’s most stable density point: the temperature at which water reaches maximum density, which was measured at the time as 4 °C.[Note 7] They concluded that one cubic decimeter of water at its maximum density was equal to 99.9265% of the target mass of the provisional kilogram standard made four years earlier.[Note 8] That same year, 1799, an all-platinum kilogram prototype was fabricated with the objective that it would equal, as close as was scientifically feasible for the day, the mass of one cubic decimeter of water at 4 °C. The prototype was presented to the Archives of the Republic in June and on 10 December 1799, the prototype was formally ratified as the kilogramme des Archives (Kilogram of the Archives) and the kilogram was defined as being equal to its mass. This standard stood for the next ninety years.
The Metre Convention was signed on 20 May 1875 and established the SI system, which since 1889 has defined the magnitude of the kilogram to be equal to the mass of the international prototype kilogram, often referred to in the professional metrology world as the "IPK". The IPK is made of a platinum alloy known as “Pt‑10Ir”, which is 90% platinum and 10% iridium (by mass) and is machined into a right-circular cylinder (height = diameter) of 39.17 millimeters to minimize its surface area. The addition of 10% iridium improved upon the all-platinum Kilogram of the Archives by greatly increasing hardness while still retaining platinum’s many virtues: extreme resistance to oxidation, extremely high density (more than twice as dense as lead and more than 21 times as dense as water), satisfactory electrical and thermal conductivities, and low magnetic susceptibility. The IPK and its six sister copies are stored at the International Bureau of Weights and Measures (known by its French-language initials BIPM) in an environmentally monitored safe in the lower vault located in the basement of the BIPM’s Pavillon de Breteuil in Sèvres on the outskirts of Paris (see External images, below, for photographs). Three independently controlled keys are required to open the vault. Official copies of the IPK were made available to other nations to serve as their national standards. These are compared to the IPK roughly every 50 years.
The IPK is one of three cylinders made in 1879. In 1883, its mass was found to be indistinguishable from that of the Kilogram of the Archives made eighty-four years prior, and was formally ratified as the kilogram by the 1st CGPM in 1889.
Modern measurements of Vienna Standard Mean Ocean Water, which is pure distilled water with an isotopic composition representative of the average of the world’s oceans, show it has a density of 0.999975 ±0.000001 kg/L at its point of maximum density (3.984 °C) under one standard atmosphere (760 torr) of pressure. Thus, a cubic decimeter of water at its point of maximum density is only 25 parts per million less massive than the IPK; that is to say, the 25 milligram difference shows that the scientists over 213 years ago managed to make the mass of the Kilogram of the Archives equal that of a cubic decimeter of water at 4 °C to within the mass of a single excess grain of rice.
By definition, the error in the measured value of the IPK's mass is exactly zero; the IPK is the kilogram. However, any changes in the IPK's mass over time can be deduced by comparing its mass to that of its official copies stored throughout the world, a process called "periodic verification". For instance, the U.S. owns four 90% platinum / 10% iridium (Pt‑10Ir) kilogram standards, two of which, K4 and K20, are from the original batch of 40 replicas delivered in 1884.[Note 10] The K20 prototype was designated as the primary national standard of mass for the U.S. Both of these, as well as those from other nations, are periodically returned to the BIPM for verification.[Note 11]
Note that none of the replicas has a mass precisely equal to that of the IPK; their masses are calibrated and documented as offset values. For instance, K20, the U.S.'s primary standard, originally had an official mass of 1 kg − 39 micrograms (μg) in 1889; that is to say, K20 was 39 µg less than the IPK. A verification performed in 1948 showed a mass of 1 kg − 19 µg. The latest verification performed in 1999 shows a mass precisely identical to its original 1889 value. Quite unlike transient variations such as this, the U.S.'s check standard, K4, has persistently declined in mass relative to the IPK—and for an identifiable reason. Check standards are used much more often than primary standards and are prone to scratches and other wear. K4 was originally delivered with an official mass of 1 kg − 75 µg in 1889, but as of 1989 was officially calibrated at 1 kg − 106 µg and ten years later was 1 kg − 116 µg. Over a period of 110 years, K4 lost 41 µg relative to the IPK.
Beyond the simple wear that check standards can experience, the mass of even the carefully stored national prototypes can drift relative to the IPK for a variety of reasons, some known and some unknown. Since the IPK and its replicas are stored in air (albeit under two or more nested bell jars), they gain mass through adsorption of atmospheric contamination onto their surfaces. Accordingly, they are cleaned in a process the BIPM developed between 1939 and 1946 known as "the BIPM cleaning method" that comprises lightly rubbing with a chamois soaked in equal parts ether and ethanol, followed by steam cleaning with bi-distilled water, and allowing the prototypes to settle for 7–10 days before verification.[Note 12] Cleaning the prototypes removes between 5 and 60 µg of contamination depending largely on the time elapsed since the last cleaning. Further, a second cleaning can remove up to 10 µg more. After cleaning—even when they are stored under their bell jars—the IPK and its replicas immediately begin gaining mass again. The BIPM even developed a model of this gain and concluded that it averaged 1.11 µg per month for the first 3 months after cleaning and then decreased to an average of about 1 µg per year thereafter. Since check standards like K4 are not cleaned for routine calibrations of other mass standards—a precaution to minimize the potential for wear and handling damage—the BIPM's model of time-dependent mass gain has been used as an "after cleaning" correction factor.
Because the first forty official copies are made of the same alloy as the IPK and are stored under similar conditions, periodic verifications using a large number of replicas—especially the national primary standards, which are rarely used—can convincingly demonstrate the stability of the IPK. What has become clear after the third periodic verification performed between 1988 and 1992 is that masses of the entire worldwide ensemble of prototypes have been slowly but inexorably diverging from each other. It is also clear that the mass of the IPK lost perhaps 50 µg over the last century, and possibly significantly more, in comparison to its official copies. The reason for this drift has eluded physicists who have dedicated their careers to the SI unit of mass. No plausible mechanism has been proposed to explain either a steady decrease in the mass of the IPK, or an increase in that of its replicas dispersed throughout the world.[Note 13] This relative nature of the changes amongst the world's kilogram prototypes is often misreported in the popular press, and even some notable scientific magazines, which often state that the IPK simply "lost 50 µg" and omit the very important caveat of "in comparison to its official copies".[Note 14] Moreover, there are no technical means available to determine whether or not the entire worldwide ensemble of prototypes suffers from even greater long-term trends upwards or downwards because their mass "relative to an invariant of nature is unknown at a level below 1000 µg over a period of 100 or even 50 years". Given the lack of data identifying which of the world’s kilogram prototypes has been most stable in absolute terms, it is equally as valid to state that the first batch of replicas has, as a group, gained an average of about 25 µg over one hundred years in comparison to the IPK.[Note 15]
What is known specifically about the IPK is that it exhibits a short-term instability of about 30 µg over a period of about a month in its after-cleaned mass. The precise reason for this short-term instability is not understood but is thought to entail surface effects: microscopic differences between the prototypes' polished surfaces, possibly aggravated by hydrogen absorption due to catalysis of the volatile organic compounds that slowly deposit onto the prototypes as well as the hydrocarbon-based solvents used to clean them.
It has been possible to rule out many explanations of the observed divergences in the masses of the world's prototypes proposed by scientists and the general public. The BIPM's FAQ explains, for example, that the divergence is dependent on the amount of time elapsed between measurements and not dependent on the number of times the artifacts have been cleaned or possible changes in gravity or environment.
Scientists are seeing far greater variability in the prototypes than previously believed. The increasing divergence in the masses of the world’s prototypes and the short-term instability in the IPK has prompted research into improved methods to obtain a smooth surface finish using diamond turning on newly manufactured replicas and has intensified the search for a new definition of the kilogram. See Proposed future definitions, below.
The stability of the IPK is crucial because the kilogram underpins much of the SI system of measurement as it is currently defined and structured. For instance, the newton is defined as the force necessary to accelerate one kilogram at one meter per second squared. If the mass of the IPK were to change slightly, so too must the newton by a proportional degree. In turn, the pascal, the SI unit of pressure, is defined in terms of the newton. This chain of dependency follows to many other SI units of measure. For instance, the joule, the SI unit of energy, is defined as that expended when a force of one newton acts through one metre. Next to be affected is the SI unit of power, the watt, which is one joule per second. The ampere too is defined relative to the newton, and ultimately, the kilogram. With the magnitude of the primary units of electricity thus determined by the kilogram, so too follow many others; namely, the coulomb, volt, tesla, and weber. Even units used in the measure of light would be affected; the candela—following the change in the watt—would in turn affect the lumen and lux.
Because the magnitude of many of the units comprising the SI system of measurement is ultimately defined by the mass of a 133-year-old, golf ball-sized piece of metal, the quality of the IPK must be diligently protected to preserve the integrity of the SI system. Yet, in spite of the best stewardship, the average mass of the worldwide ensemble of prototypes and the mass of the IPK have likely diverged another 5.4 µg since the third periodic verification 23 years ago.[Note 16] Further, the world’s national metrology laboratories must wait for the fourth periodic verification to confirm whether the historical trends persisted.
Fortunately, definitions of the SI units are quite different from their practical realizations. For instance, the meter is defined as the distance light travels in a vacuum during a time interval of 1⁄299,792,458 of a second. However, the meter’s practical realization typically takes the form of a helium–neon laser, and the meter’s length is delineated—not defined—as 1,579,800.298728 wavelengths of light from this laser. Now suppose that the official measurement of the second was found to have drifted by a few parts per billion (it is actually extremely stable with a reproducibility of a few parts in 1015). There would be no automatic effect on the meter because the second—and thus the meter’s length—is abstracted via the laser comprising the meter’s practical realization. Scientists performing meter calibrations would simply continue to measure out the same number of laser wavelengths until an agreement was reached to do otherwise. The same is true with regard to the real-world dependency on the kilogram: if the mass of the IPK was found to have changed slightly, there would be no automatic effect upon the other units of measure because their practical realizations provide an insulating layer of abstraction. Any discrepancy would eventually have to be reconciled though because the virtue of the SI system is its precise mathematical and logical harmony amongst its units. If the IPK’s value were definitively proven to have changed, one solution would be to simply redefine the kilogram as being equal to the mass of the IPK plus an offset value, similarly to what is currently done with its replicas; e.g., “the kilogram is equal to the mass of the IPK + 42 parts per billion” (equivalent to 42 µg).
The long-term solution to this problem, however, is to liberate the SI system’s dependency on the IPK by developing a practical realization of the kilogram that can be reproduced in different laboratories by following a written specification. The units of measure in such a practical realization would have their magnitudes precisely defined and expressed in terms of fundamental physical constants. While major portions of the SI system would still be based on the kilogram, the kilogram would in turn be based on invariant, universal constants of nature. Much work towards that end is ongoing, though no alternative has yet achieved the uncertainty of 20 parts per billion (~20 µg) required to improve upon the IPK. However, as of April 2007[update], the U.S.’s National Institute of Standards and Technology (NIST) had an implementation of the watt balance that was approaching this goal, with a demonstrated uncertainty of 36 µg. See Watt balance, below.
The avoirdupois pound, used in both the imperial system and U.S. customary units, is defined as exactly 0.45359237 kg, making one kilogram approximately equal to 2.2046 avoirdupois pounds. Although both the avoirdupois (or international) pound and the kilogram are units of mass and have related unit of force the pound-force, the kilogram-force is seldom used.
As of 2011 the kilogram was the only SI unit still defined by an artifact. In 1960 the meter having also been defined as an artifact (a single platinum-iridium bar with two marks on it) was redefined in terms of invariant, fundamental physical constants (the wavelength of light emitted by krypton, and later the speed of light) so that the standard can be reproduced in different laboratories by following a written specification. At the 94th Meeting of the International Committee for Weights and Measures (2005) it was recommended that the same be done with the kilogram.
In October 2010, the International Committee for Weights and Measures (known by its French-language initials CIPM) voted to submit a resolution for consideration at the General Conference on Weights and Measures (CGPM), to "take note of an intention" that the kilogram be defined in terms of the Planck constant, h. This resolution was accepted by the 24th conference of the CGPM in October 2011 and in addition the date of the 25th conference was moved forward from 2015 to 2014. Such a definition would theoretically permit any apparatus that was capable of delineating the kilogram in terms of the Planck constant to be used as long as it possessed sufficient precision, accuracy and stability. The watt balance (discussed below) may be able to do this.
In getting to the threshold of replacing the last artifact that underpins much of the International System of Units (SI), a variety of other very different technologies and approaches were considered and explored over many years. They too are covered below. Some of these now-abandoned approaches were based on equipment and procedures that would have enabled the reproducible production of new, kilogram-mass prototypes on demand (albeit with extraordinary effort) using measurement techniques and material properties that are ultimately based on, or traceable to, fundamental constants. Others were based on devices that measured either the acceleration or weight of hand-tuned, kilogram test masses and which expressed their magnitudes in electrical terms via special components that permit traceability to fundamental constants. All approaches depend on converting a weight measurement to a mass, and therefore require the precise measurement of the strength of gravity in laboratories. All approaches would have precisely fixed one or more constants of nature at a defined value.
The watt balance is essentially a single-pan weighing scale that measures the electric power necessary to oppose the weight of a kilogram test mass as it is pulled by earth’s gravity. It is a variation of an ampere balance in that it employs an extra calibration step that nulls the effect of geometry. The electric potential in the watt balance is delineated by a Josephson voltage standard, which allows voltage to be linked to an invariant constant of nature with extremely high precision and stability. Its circuit resistance is calibrated against a quantum Hall resistance standard.
The watt balance requires exquisitely precise measurement of the local gravitational acceleration g in the laboratory, using a gravimeter. (See “FG‑5 absolute gravimeter” in External images, below). For instance, the NIST compensates for earth’s gravity gradient of 309 µGal per meter when the elevation of the center of the gravimeter differs from that of the nearby test mass in the watt balance; a change in the weight of a one-kilogram test mass that equates to about 316 µg/m.
In April 2007, the NIST’s implementation of the watt balance demonstrated a combined relative standard uncertainty (CRSU) of 36 µg and a short-term resolution of 10–15 µg.[Note 17] The UK’s National Physical Laboratory’s watt balance demonstrated a CRSU of 70.3 µg in 2007. That watt balance was disassembled and shipped in 2009 to Canada’s Institute for National Measurement Standards (part of the National Research Council), where research and development with the device could continue.
If the CGPM adopts the new proposal and the new definition of the kilogram becomes part of the SI, the Planck constant (h), which is a measure that relates the energy of photons to their frequency, would be precisely fixed (the currently accepted value of 6.62606957(29)×10−34 J s has an uncertainty of plus or minus 29 counts in its last two digits).[Note 18] Once agreed upon internationally, the kilogram would no longer be defined as the mass of the IPK. All the remaining units in the International System of Units (the SI) that today have dependencies upon the kilogram and the joule would also fall in place, their magnitudes ultimately defined, in part, in terms of photon oscillations rather than the IPK.
Gravity and the nature of the watt balance, which oscillates test masses up and down against the local gravitational acceleration g, are exploited so that mechanical power is compared against electrical power, which is the square of voltage divided by electrical resistance. However, g varies significantly—nearly one percent—depending upon where on earth’s surface the measurement is made (see Earth’s gravity ). There are also subtle seasonal variations in g due to changes in underground water tables, and larger semimonthly and diurnal changes due to tidal distortions in the earth’s shape caused by the moon. Although g would not be a term in the definition of the kilogram, it would be crucial in the delineation of the kilogram when relating energy to power. Accordingly, g must be measured with at least as much precision and accuracy as are the other terms, so measurements of g must also be traceable to fundamental constants of nature. For the most precise work in mass metrology, g is measured using dropping-mass absolute gravimeters that contain an iodine-stabilized helium–neon laser interferometer. The fringe-signal, frequency-sweep output from the interferometer is measured with a rubidium atomic clock. Since this type of dropping-mass gravimeter derives its accuracy and stability from the constancy of the speed of light as well as the innate properties of helium, neon, and rubidium atoms, the ‘gravity’ term in the delineation of an all-electronic kilogram is also measured in terms of invariants of nature—and with very high precision. For instance, in the basement of the NIST’s Gaithersburg facility in 2009, when measuring the gravity acting upon Pt‑10Ir test masses (which are denser, smaller, and have a slightly lower center of gravity inside the watt balance than stainless steel masses), the measured value was typically within 8 ppb of 9.80101644 m/s2.
The virtue of electronic realizations like the watt balance is that the definition and dissemination of the kilogram would no longer be dependent upon the stability of kilogram prototypes, which must be very carefully handled and stored. It would free physicists from the need to rely on assumptions about the stability of those prototypes. Instead, hand-tuned, close-approximation mass standards would simply be weighed and documented as being equal to one kilogram plus an offset value. With the watt balance, while the kilogram would be delineated in electrical and gravity terms, all of which are traceable to invariants of nature; it would be defined in a manner that is directly traceable to just three fundamental constants of nature. The Planck constant defines the kilogram in terms of the second and the meter. By fixing the Planck constant, the definition of the kilogram would depend only on the definitions of the second and the meter. The definition of the second depends on a single defined physical constant: the ground state hyperfine splitting frequency of the caesium 133 atom Δν(133Cs)hfs. The meter depends on the second and on an additional defined physical constant: the speed of light c. If the kilogram is redefined in this manner, mass artifacts—physical objects calibrated in a watt balance, including the IPK—would no longer be part of the definition, but would instead become transfer standards.
Scales like the watt balance also permit more flexibility in choosing materials with especially desirable properties for mass standards. For instance, Pt‑10Ir could continue to be used so that the specific gravity of newly produced mass standards would be the same as existing national primary and check standards (≈21.55 g/ml). This would reduce the relative uncertainty when making mass comparisons in air. Alternatively, entirely different materials and constructions could be explored with the objective of producing mass standards with greater stability. For instance, osmium-iridium alloys could be investigated if platinum’s propensity to absorb hydrogen (due to catalysis of VOCs and hydrocarbon-based cleaning solvents) and atmospheric mercury proved to be sources of instability. Also, vapor-deposited, protective ceramic coatings like nitrides could be investigated for their suitability to isolate these new alloys.
The challenge with watt balances is not only in reducing their uncertainty, but also in making them truly practical realizations of the kilogram. Nearly every aspect of watt balances and their support equipment requires such extraordinarily precise and accurate, state-of-the-art technology that—unlike a device like an atomic clock—few countries would currently choose to fund their operation. For instance, the NIST’s watt balance used four resistance standards in 2007, each of which was rotated through the watt balance every two to six weeks after being calibrated in a different part of NIST headquarters facility in Gaithersburg, Maryland. It was found that simply moving the resistance standards down the hall to the watt balance after calibration altered their values 10 ppb (equivalent to 10 µg) or more. Present-day technology is insufficient to permit stable operation of watt balances between even biannual calibrations. If the kilogram is defined in terms of the Planck constant, it is likely there will only be a few—at most—watt balances initially operating in the world.
Alternative approaches to redefining the kilogram that were fundamentally different from the watt balance were explored to varying degrees with some abandoned, as follows:
Though not offering a practical realization, this definition would precisely define the magnitude of the kilogram in terms of a certain number of carbon‑12 atoms. Carbon‑12 (12C) is an isotope of carbon. The mole is currently defined as “the quantity of entities (elementary particles like atoms or molecules) equal to the number of atoms in 12 grams of carbon‑12.” Thus, the current definition of the mole requires that 1000⁄12 (83⅓) moles of 12C has a mass of precisely one kilogram. The number of atoms in a mole, a quantity known as the Avogadro constant, is experimentally determined, and the current best estimate of its value is 6.02214129(27)×1023 entities per mole. This new definition of the kilogram proposed to fix the Avogadro constant at precisely 6.02214X×10 23 with the kilogram being defined as “the mass equal to that of 1000⁄12 · 6.02214X×10 23 atoms of 12C.”
The accuracy of the measured value of the Avogadro constant is currently limited by the uncertainty in the value of the Planck constant—a measure relating the energy of photons to their frequency. That relative standard uncertainty has been 50 parts per billion (ppb) since 2006. By fixing the Avogadro constant, the practical effect of this proposal would be that the uncertainty in the mass of a 12C atom—and the magnitude of the kilogram—could be no better than the current 50 ppb uncertainty in the Planck constant. Under this proposal, the magnitude of the kilogram would be subject to future refinement as improved measurements of the value of the Planck constant become available; electronic realizations of the kilogram would be recalibrated as required. Conversely, an electronic definition of the kilogram (see Electronic approaches, below), which would precisely fix the Planck constant, would continue to allow 83⅓ moles of 12C to have a mass of precisely one kilogram but the number of atoms comprising a mole (the Avogadro constant) would continue to be subject to future refinement.
A variation on a 12C-based definition proposes to define the Avogadro constant as being precisely 84,446,8893 (≈6.02214162×1023) atoms. An imaginary realization of a 12-gram mass prototype would be a cube of 12C atoms measuring precisely 84,446,889 atoms across on a side. With this proposal, the kilogram would be defined as “the mass equal to 84,446,8893 × 83⅓ atoms of 12C.”[Note 19]
Another Avogadro constant-based approach, known as the Avogadro project, would define and delineate the kilogram as a softball-size (93.6 mm diameter) sphere of silicon atoms. Silicon was chosen because a commercial infrastructure with mature processes for creating defect-free, ultra-pure monocrystalline silicon already exists to service the semiconductor industry. To make a practical realization of the kilogram, a silicon boule (a rod-like, single-crystal ingot) would be produced. Its isotopic composition would be measured with a mass spectrometer to determine its average relative atomic mass. The boule would be cut, ground, and polished into spheres. The size of a select sphere would be measured using optical interferometry to an uncertainty of about 0.3 nm on the radius—roughly a single atomic layer. The precise lattice spacing between the atoms in its crystal structure (≈192 pm) would be measured using a scanning X-ray interferometer. This permits its atomic spacing to be determined with an uncertainty of only three parts per billion. With the size of the sphere, its average atomic mass, and its atomic spacing known, the required sphere diameter can be calculated with sufficient precision and low uncertainty to enable it to be finish-polished to a target mass of one kilogram.
Experiments are being performed on the Avogadro Project’s silicon spheres to determine whether their masses are most stable when stored in a vacuum, a partial vacuum, or ambient pressure. However, no technical means currently exist to prove a long-term stability any better than that of the IPK’s because the most sensitive and accurate measurements of mass are made with dual-pan balances like the BIPM’s FB‑2 flexure-strip balance (see External links, below). Balances can only compare the mass of a silicon sphere to that of a reference mass. Given the latest understanding of the lack of long-term mass stability with the IPK and its replicas, there is no known, perfectly stable mass artifact to compare against. Single-pan scales, which measure weight relative to an invariant of nature, are not precise to the necessary long-term uncertainty of 10–20 parts per billion. Another issue to be overcome is that silicon oxidizes and forms a thin layer (equivalent to 5–20 silicon atoms) of silicon dioxide (quartz) and silicon monoxide. This layer slightly increases the mass of the sphere, an effect which must be accounted for when polishing the sphere to its finished dimension. Oxidation is not an issue with platinum and iridium, both of which are noble metals that are roughly as cathodic as oxygen and therefore don’t oxidize unless coaxed to do so in the laboratory. The presence of the thin oxide layer on a silicon-sphere mass prototype places additional restrictions on the procedures that might be suitable to clean it to avoid changing the layer’s thickness or oxide stoichiometry.
All silicon-based approaches would fix the Avogadro constant but vary in the details of the definition of the kilogram. One approach would use silicon with all three of its natural isotopes present. About 7.78% of silicon comprises the two heavier isotopes: 29Si and 30Si. As described in Carbon‑12 above, this method would define the magnitude of the kilogram in terms of a certain number of 12C atoms by fixing the Avogadro constant; the silicon sphere would be the practical realization. This approach could accurately delineate the magnitude of the kilogram because the masses of the three silicon nuclides relative to 12C are known with great precision (relative uncertainties of 1 ppb or better). An alternative method for creating a silicon sphere-based kilogram proposes to use isotopic separation techniques to enrich the silicon until it is nearly pure 28Si, which has a relative atomic mass of 27.9769265325(19). With this approach, the Avogadro constant would not only be fixed, but so too would the atomic mass of 28Si. As such, the definition of the kilogram would be decoupled from 12C and the kilogram would instead be defined as 1000⁄27.9769265325 · 6.02214179×1023 atoms of 28Si (≈35.74374043 fixed moles of 28Si atoms). Physicists could elect to define the kilogram in terms of 28Si even when kilogram prototypes are made of natural silicon (all three isotopes present). Even with a kilogram definition based on theoretically pure 28Si, a silicon-sphere prototype made of only nearly pure 28Si would necessarily deviate slightly from the defined number of moles of silicon to compensate for various chemical and isotopic impurities as well as the effect of surface oxides.
Another Avogadro-based approach, ion accumulation, since abandoned, would have defined and delineated the kilogram by precisely creating new metal prototypes on demand. It would have done so by accumulating gold or bismuth ions (atoms stripped of an electron) and counted them by measuring the electrical current required to neutralize the ions. Gold (197Au) and bismuth (209Bi) were chosen because they can be safely handled and have the two highest atomic masses among the mononuclidic elements that is effectively non-radioactive (bismuth) or is perfectly stable (gold). See also Table of nuclides.[Note 21]
With a gold-based definition of the kilogram for instance, the relative atomic mass of gold could have been fixed as precisely 196.9665687, from the current value of 196.9665687(6). As with a definition based upon carbon‑12, the Avogadro constant would also have been fixed. The kilogram would then have been defined as “the mass equal to that of precisely 1000⁄196.9665687 · 6.02214179×1023 atoms of gold” (precisely 3,057,443,620,887,933,963,384,315 atoms of gold or about 5.07700371 fixed moles).
In 2003, German experiments with gold at a current of only 10 µA demonstrated a relative uncertainty of 1.5%. Follow-on experiments using bismuth ions and a current of 30 mA were expected to accumulate a mass of 30 g in six days and to have a relative uncertainty of better than 1 ppm. Ultimately, ion‑accumulation approaches proved to be unsuitable. Measurements required months and the data proved too erratic for the technique to be considered a viable future replacement to the IPK.
Among the many technical challenges of the ion-deposition apparatus was obtaining a sufficiently high ion current (mass deposition rate) while simultaneously decelerating the ions so they could all deposit onto a target electrode embedded in a balance pan. Experiments with gold showed the ions had to be decelerated to very low energies to avoid sputtering effects—a phenomenon whereby ions that had already been counted ricochet off the target electrode or even dislodged atoms that had already been deposited. The deposited mass fraction in the 2003 German experiments only approached very close to 100% at ion energies of less than around 1 eV (<1 km/s for gold).
If the kilogram had been defined as a precise quantity of gold or bismuth atoms deposited with an electric current, not only would the Avogadro constant and the atomic mass of gold or bismuth have to have been precisely fixed, but also the value of the elementary charge (e), likely to 1.60217X×10 −19 C (from the currently recommended value of 1.602176565(35)×10−19 C). Doing so would have effectively defined the ampere as a flow of 1⁄1.60217X×10 −19 electrons per second past a fixed point in an electric circuit. The SI unit of mass would have been fully defined by having precisely fixed the values of the Avogadro constant and elementary charge, and by exploiting the fact that the atomic masses of bismuth and gold atoms are invariant, universal constants of nature.
Beyond the slowness of making a new mass standard and the poor reproducibility, there were other intrinsic shortcomings to the ion‑accumulation approach that proved to be formidable obstacles to ion-accumulation-based techniques becoming a practical realization. The apparatus necessarily required that the deposition chamber have an integral balance system to enable the convenient calibration of a reasonable quantity of transfer standards relative to any single internal ion-deposited prototype. Furthermore, the mass prototypes produced by ion deposition techniques would have been nothing like the freestanding platinum-iridium prototypes currently in use; they would have been deposited onto—and become part of—an electrode imbedded into one pan of a special balance integrated into the device. Moreover, the ion-deposited mass wouldn’t have had a hard, highly polished surface that can be vigorously cleaned like those of current prototypes. Gold, while dense and a noble metal (resistant to oxidation and the formation of other compounds), is extremely soft so an internal gold prototype would have to be kept well isolated and scrupulously clean to avoid contamination and the potential of wear from having to remove the contamination. Bismuth, which is an inexpensive metal used in low-temperature solders, slowly oxidizes when exposed to room-temperature air and forms other chemical compounds and so would not have produced stable reference masses unless it was continually maintained in a vacuum or inert atmosphere.
This approach would define the kilogram as “the mass which would be accelerated at precisely 2×10−7 m/s2 when subjected to the per-meter force between two straight parallel conductors of infinite length, of negligible circular cross section, placed one meter apart in vacuum, through which flow a constant current of 1⁄1.60217X×10 −19 elementary charges per second”.
Effectively, this would define the kilogram as a derivative of the ampere rather than present relationship, which defines the ampere as a derivative of the kilogram. This redefinition of the kilogram would specify elementary charge (e) as precisely 1.60217X×10 −19 coulomb rather than the current recommended value of 1.602176565(35)×10−19 C. It would necessarily follow that the ampere (one coulomb per second) would also become an electrical current of this precise quantity of elementary charges per second passing a given point in an electric circuit. The virtue of a practical realization based upon this definition is that unlike the watt balance and other scale-based methods, all of which require the careful characterization of gravity in the laboratory, this method delineates the magnitude of the kilogram directly in the very terms that define the nature of mass: acceleration due to an applied force. Unfortunately, it is extremely difficult to develop a practical realization based upon accelerating masses. Experiments over a period of years in Japan with a superconducting, 30 g mass supported by diamagnetic levitation never achieved an uncertainty better than ten parts per million. Magnetic hysteresis was one of the limiting issues. Other groups performed similar research that used different techniques to levitate the mass.
Because SI prefixes may not be concatenated (serially linked) within the name or symbol for a unit of measure, SI prefixes are used with the gram, not the kilogram, which already has a prefix as part of its name. For instance, one-millionth of a kilogram is 1 mg (one milligram), not 1 µkg (one microkilogram).
|10−1 g||dg||decigram||101 g||dag||decagram|
|10−2 g||cg||centigram||102 g||hg||hectogram|
|10−3 g||mg||milligram||103 g||kg||kilogram|
|10−6 g||µg||microgram (mcg)||106 g||Mg||megagram (tonne)|
|10−9 g||ng||nanogram||109 g||Gg||gigagram|
|10−12 g||pg||picogram||1012 g||Tg||teragram|
|10−15 g||fg||femtogram||1015 g||Pg||petagram|
|10−18 g||ag||attogram||1018 g||Eg||exagram|
|10−21 g||zg||zeptogram||1021 g||Zg||zettagram|
|10−24 g||yg||yoctogram||1024 g||Yg||yottagram|
|Common prefixes are in bold face.[Note 22]|
As regards the kilogram, relativity’s effect upon the constancy of matter’s mass is simply an interesting scientific phenomenon that has zero effect on the definition of the kilogram and its practical realizations.
France’s metric system had been championed by Charles Maurice de Talleyrand‑Périgord. On 30 March 1791, four days after Talleyrand forwarded a specific proposal on how to proceed with the project, the French government ordered a committee known as the Academy to commence work on accurately determining the magnitude of the base units of the new metric system. The Academy divided the task among five commissions. The commission charged with determining the mass of a cubic decimeter of water originally comprised Lavoisier and Haüy but their work was finished by Louis Lefèvre‑Gineau and Giovanni Fabbroni.
Neither Lavoisier nor Haüy can be blamed for participating in an initial—and inaccurate—measurement and for leaving the final work to Lefèvre‑Gineau and Fabbroni to finish in 1799. As a member of the Ferme générale, Lavoisier was also one of France’s 28 tax collectors. He was consequently convicted of treason during the waning days of the Reign of Terror period of the French Revolution and beheaded on 8 May 1794. Lavoisier’s partner, Haüy, was also thrown into prison and was himself at risk of going to the guillotine but his life was spared after a renowned French naturalist interceded.
Many theories have been advanced to explain the divergence in the masses of the prototypes. One theory posits that the relative change in mass between the IPK and its replicas is not one of loss at all and is instead a simple matter that the IPK has gained less than the replicas. This theory begins with the observation that the IPK is uniquely stored under three nested bell jars whereas its six sister copies stored alongside it in the vault as well as the other replicas dispersed throughout the world are stored under only two. This theory is also founded on two other facts: that platinum has a strong affinity for mercury, and that atmospheric mercury is significantly more abundant in the atmosphere today than at the time the IPK and its replicas were manufactured. The burning of coal is a major contributor to atmospheric mercury and both Denmark and Germany have high coal shares in electrical generation. Conversely, electrical generation in France, where the IPK is stored, is mostly nuclear. This theory is supported by the fact that the mass divergence rate—relative to the IPK—of Denmark’s prototype, K48, since it took possession in 1949 is an especially high 78 µg per century while that of Germany’s prototype has been even greater at 126 µg/century ever since it took possession of K55 in 1954. However, still other data for other replicas isn’t supportive of this theory. This mercury absorption theory is just one of many advanced by the specialists to account for the relative change in mass. To date, each theory has either proven implausible, or there are insufficient data or technical means to either prove or disprove it.
|BIPM: The IPK in three nested bell jars|
|NIST: K20, the US National Prototype Kilogram resting on an egg crate fluorescent light panel|
|BIPM: Steam cleaning a 1 kg prototype before a mass comparison|
|BIPM: The IPK and its six sister copies in their vault|
|The Age: Silicon sphere for the Avogadro Project|
|NPL: The NPL’s Watt Balance project|
|NIST: This particular Rueprecht Balance, an Austrian-made precision balance, was used by the NIST from 1945 until 1960|
|BIPM: The FB‑2 flexure-strip balance, the BIPM’s modern precision balance featuring a standard deviation of one ten-billionth of a kilogram (0.1 µg)|
|BIPM: Mettler HK1000 balance, featuring 1 µg resolution and a 4 kg maximum mass. Also used by NIST and Sandia National Laboratories’ Primary Standards Laboratory|
|Micro-g LaCoste: FG‑5 absolute gravimeter, (diagram), used in national laboratories to measure gravity to 2 µGal accuracy|
Media related to Kilogram at Wikimedia Commons
Contenu de sensagent
Dictionnaire et traducteur pour mobile
Nouveau : sensagent est maintenant disponible sur votre mobile
dictionnaire et traducteur pour sites web
Une fenêtre (pop-into) d'information (contenu principal de Sensagent) est invoquée un double-clic sur n'importe quel mot de votre page web. LA fenêtre fournit des explications et des traductions contextuelles, c'est-à-dire sans obliger votre visiteur à quitter votre page web !
Avec la boîte de recherches Sensagent, les visiteurs de votre site peuvent également accéder à une information de référence pertinente parmi plus de 5 millions de pages web indexées sur Sensagent.com. Vous pouvez Choisir la taille qui convient le mieux à votre site et adapter la charte graphique.
Solution commerce électronique
Augmenter le contenu de votre site
Ajouter de nouveaux contenus Add à votre site depuis Sensagent par XML.
Parcourir les produits et les annonces
Obtenir des informations en XML pour filtrer le meilleur contenu.
Indexer des images et définir des méta-données
Fixer la signification de chaque méta-donnée (multilingue).
Renseignements suite à un email de description de votre projet.
Jeux de lettres
Lettris est un jeu de lettres gravitationnelles proche de Tetris. Chaque lettre qui apparaît descend ; il faut placer les lettres de telle manière que des mots se forment (gauche, droit, haut et bas) et que de la place soit libérée.
Il s'agit en 3 minutes de trouver le plus grand nombre de mots possibles de trois lettres et plus dans une grille de 16 lettres. Il est aussi possible de jouer avec la grille de 25 cases. Les lettres doivent être adjacentes et les mots les plus longs sont les meilleurs. Participer au concours et enregistrer votre nom dans la liste de meilleurs joueurs ! Jouer
Dictionnaire de la langue française
La plupart des définitions du français sont proposées par SenseGates et comportent un approfondissement avec Littré et plusieurs auteurs techniques spécialisés.
Le dictionnaire des synonymes est surtout dérivé du dictionnaire intégral (TID).
L'encyclopédie française bénéficie de la licence Wikipedia (GNU).
Les jeux de lettres anagramme, mot-croisé, joker, Lettris et Boggle sont proposés par Memodata.
Le service web Alexandria est motorisé par Memodata pour faciliter les recherches sur Ebay. La SensagentBox est offerte par sensAgent.
Changer la langue cible pour obtenir des traductions.
Astuce: parcourir les champs sémantiques du dictionnaire analogique en plusieurs langues pour mieux apprendre avec sensagent.